SymProjects Forum

General Category => General Discussions => Topic started by: steve o on March 19, 2017, 04:47:59 pm

Title: Dials set up problem
Post by: steve o on March 19, 2017, 04:47:59 pm

Can any body advise as im having trouble with  this ,i set my dials up  have them all set up and enabled ,then when i  switch off for the night i have to set then all up again the next day, painfull

Title: Re: Dials set up problem
Post by: Cristiano on March 20, 2017, 09:55:56 am

Hello.
You are not supposed to configure the gauges every day, so there must be a problem somewhere.

When you open the Pro-Gauge configuration screen in Simdash the day after, can you see the configuration you set the day before? or is it back to the default values?

regards
Cristiano

Title: Re: Dials set up problem
Post by: steve o on March 20, 2017, 10:29:19 am

Hi, yes it goes back to default mode as if you was starting from the beginning with the set up with the dials, if you can advise that would be helpful in this matter, thanks steve o

Title: Re: Dials set up problem
Post by: Cristiano on March 20, 2017, 10:51:35 am

ok.
when you open the Pro-Gauge configuration screen in SimDash, on the top-left corner there is a 3 digits number. it is the serial number of the controller. it is used when saving the settings. can you see the number? or is it a sequence of random characters instead?

Title: Re: Dials set up problem
Post by: steve o on March 20, 2017, 11:31:21 am

I wll look tonight and report back,what happen after that in case I see something

Title: Re: Dials set up problem
Post by: steve o on March 20, 2017, 08:25:21 pm

Hi Cristiano,i had a look and i have this in top left corner SN: thens is blank with nothing no letters or numbers  on the configuration screen,steve

Title: Re: Dials set up problem
Post by: Cristiano on March 21, 2017, 03:47:01 pm

Hello.
I believe the problem is with the serial  number of the Pro-Gauge. if is displayed on the top left corner of the configuration screen and if should be a 3 digit number.
in your case it is invalid and it must be reset.

to do it, follow these instructions:

Edit SimDash.exe.config which is in the SimDash' installation folder and change these lines:

        <setting name="ShowTestControls" serializeAs="String">
          <value>False</value>
        </setting>

to:

        <setting name="ShowTestControls" serializeAs="String">
          <value>True</value>
        </setting>

Start SimDash.
In the Pro-Gauge configuration screen  (RPM section) there is a button that says "Set Serial Number"
Click it and confirm
Unplug and plug the board in again
Now a new serial number is set in the Pro-Gauge and you should be able to save the configuration.

Title: Re: Dials set up problem
Post by: steve o on March 22, 2017, 10:05:26 am

Hi I'm still struggling with this  :)when you say set serial number I fall to see the button to click on, im starting to get totally embarrassing  :)I think I need a step by step plan to be a happy man,steve

Title: Re: Dials set up problem
Post by: Cristiano on March 22, 2017, 04:35:34 pm

Hello.
If you make the changes that I suggested, when you start SimDash and open the Pro-Gauge configuration screen, the RPM section should look like this:

https://www.dropbox.com/s/ysx54f0pfcqukwm/pg.png?dl=0

Notice the serial number displayed on the top left corner: 251

and the big button at the botton that will allow you to set a new serial number if you need to.

Let me know if you have questions.

Cristiano

Title: Re: Dials set up problem
Post by: steve o on March 23, 2017, 09:11:01 pm

Great news Cristiano ,after many tries and fails it  seems to be working again can't thank you enough for your help in this matter im really pleased ,now i just need to fine tune them to be the same as in game ,how would you go about it  im not to fair away now is it trail and error until you happy with it  but thanks again it took a while but i got it done in the end ,steve

Title: Re: Dials set up problem
Post by: Cristiano on March 24, 2017, 10:25:45 am

Hello.
I think the Pro-Gauge page on the website contains all the information you need to configure the gauges. it is a one-off operation.
But if something is not clear, please let me know.

regards
Cristiano