Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - bonjourno38

Pages: [1] 2
1
General Discussions / Re: Ferrari Dial
« on: July 03, 2011, 05:02:57 pm »
Hi,

Very good job Fahim !!!!! Where have you find your instrument cluster ?
The two gauges on the left are working with the game ?

Bye.

2
General Discussions / Re: Aussie Commodore VT dash
« on: May 25, 2011, 09:22:29 pm »
Hello,

Fantastic job RT1971. I have just a question for you: Can you take photos of the connector on the back of your Dash please ?
In fact, I want to see if I can use the 20 pin dual female splittable jumper wire for my Alfa 156 Cluster, because I haven't find the connectors...
Thanks.

Bye.

3
General Discussions / Re: My cockpit build Log(WIP)
« on: May 02, 2011, 02:21:47 pm »
UP

4
General Discussions / Re: My cockpit build Log(WIP)
« on: April 27, 2011, 07:19:27 pm »
Hello,

Thanks for your answer. What I wanted to say before is that:

How many son 12V and earth have you connected to the speedometer and tachometer ?
What are the numbers of the plugs on cluster you have used for plugs the + and - outputs of the revburner ?
What is the number of the plugs for the light of the tachometer and speedometer because I want to put switches for light ?

Thanks.

Bye.




Connector A, 16-way

1, Earth
2, N.C.
3, Check module warning light test
4, Central module warning light test
5, Seat belt warning light
6, N.C.
7, Outdoor temperature signal input
8, N.C.
9, Direct supply
10, Ignition-operated supply
11, Speedometer signal input
12, Central module lighting
13, Water in diesel filter warning light
14, Speedometer signal output (N.C.)
15, Speedometer signal output (to i.e. control unit)
16, Speedometer signal output (to air conditioner control unit)

Connector B, 12-way

1, Heater plugs warning light
2, Passenger Air Bag disabled warning light
3, Rev counter warning light test
4, Rev counter module lighting
5, Side light signal
6, Lighting dimmer signal
7, N.C.
8, N.C.
9, N.C.
10, N.C.
11, Brake pad wear warning light
12, Trip counter reset signal


Rev Counter:

Connector A, 20-way

1, Right rear side light
2, Left front side light output
3, Side light signal
4, Left rear fog lamp signal
5, Brake light signal
6, Side light for trailer
7, Rear fog lamp for trailer
8, Dipped beam enablement
9, Left rear side light
10, Direct power supply for check (left branch)
11, Left number plate light
12, Right number plate light
13, Right brake light
14, Earth
15, Supply controlled by the ignition
16, Direct supply for check (right branch)
17, Right rear fog lamp
18, Left brake light
19, Brake light for trailer
20, Right front side light

Connector B, 16-way

1, Rear fog lamps warning light
2, Trailer direction indicators warning light
3, Rev counter module lighting
4, Main beam headlamps warning light
5, Low oil pressure warning light
6, Engine rpm signal input
7, Recharging warning light
8, Engine rpm signal output
9, Left direction indicators warning light
10, Rev counter module warning light test
11, N.C.
12, Automatic transmission display (N.C.)
13, N.C.
14, Fog lamp warning light
15, Fuel injection/EOBD fault warning light
16, Right turn signal warning light



5
General Discussions / Re: My cockpit build Log(WIP)
« on: April 25, 2011, 01:43:49 pm »
Up

6
General Discussions / Re: My cockpit build Log(WIP)
« on: April 22, 2011, 12:33:57 am »
Hello,

Thanks for that list Nescafe, it will be more easier for me to do the good plugs.
Can you just say the number of trips you used especially for the +12 V and earth.
What type of power supply have you used ?

Thanks a lot. Bye.

7
General Discussions / Re: My cockpit build Log(WIP)
« on: April 19, 2011, 11:04:05 pm »
Hello Nescafe37,

Finally, I'm going to have a 156 2.5 V6 instrument cluster, and I want to know if you can give me the wiring diagrams of the 156 cluster, or if you can give me photos to the back of the cluster because I want to see your plugs please.
I salute once again your work that I find beautiful.
Cristiano thank you also has to offer these great products.

Bye.

8
Show off your build / Re: My cockpit build WIP
« on: April 13, 2011, 07:01:53 pm »
Hello,

I hope that the precedent wiring diagrams are the same for the M3 E36 cluster.....
Where can I buy the followings connectors ?

What is the price for that connectors ?

Thanks for your answer....

9
Show off your build / Re: My cockpit build WIP
« on: April 12, 2011, 06:59:45 pm »
Hello,

Finally, I'm going to buy M3 E36 dashboard. Can you give me the wiring diagrams please. I hope you have them....

Thanks, Bye.


10
General Discussions / Re: My Cockpit build WIP (Chris P Duck)
« on: April 08, 2011, 11:28:37 pm »
Hello,

Thanks for your answer, your cockpit is very beautiful, and I'm impressed by your work.
Are you tried to run some lights on your dashboard as additional LED from SLI-M?
I have that Idea for my future Dashboard, because I have an SLI-Pro and I want to run the light indicator for headlights, oil temperature and other with my SLI would be great ...

Thanks.

A+.

11
General Discussions / Re: My Cockpit build WIP (Chris P Duck)
« on: April 08, 2011, 04:58:44 pm »
Hello,

How many power supply do you use? What are her powers (V and A)?
How did you choose?

Thanks, and congratulations for your work.

Bye.

12
General Discussions / Re: My cockpit build Log(WIP)
« on: April 07, 2011, 11:55:09 pm »
Hello,

I have others questions for you:

-If I use an external 12V, 3A power supply for supply the Dashboard, Should I supply the revburners with other 500mA power supplies via their DC outputs ?
-A power supply 3A/12V does she not give too power for a dahsboard? That is will not to break him ?

Thanks for answers.

Bye.

13
General Discussions / Re: My cockpit build Log(WIP)
« on: April 06, 2011, 11:57:58 pm »
Hello,

Thank you for all your answers, I think I don't have other questions for the moment.
I thank you a lot for your help,  I expect to have the dashboard and after I order my revburners.
If I have other questions, I will post here later...
@Nescafe and Mortos: Thanks for the manual of the GTV.

PS: Nescafe, can you post others photos with the plug on the Revburners ?

A+.

14
General Discussions / Re: My cockpit build Log(WIP)
« on: April 05, 2011, 11:53:54 pm »
Hello,

Thanks for your answers, but I have some other questions for you today:

-How can I find the wires + and - of the power supply if there is a 2.1mm or 5.5mm plug ? I should cut the wire before that plug ?
-If I test on all the single connectors, I will not break the dashboard ?
-Can you give me photos of your different installations (particulary the revburners photos and the 156 dashboard) ?

Thanks for your fast answers...  Soon I'll be able to order my 2 revburners With your help fast.

Bye.

Cordially, Florian.

15
General Discussions / Re: My cockpit build Log(WIP)
« on: April 04, 2011, 10:36:51 pm »
Hi,

To begin, thanks for your very fast answer. But I have bad news for you, your answers have led to further questions from me ;D.
I have seen the wiring diagrams of a power supply. But I don't Understand something...

-How can I plug the + or - of the power supply to the Revburners ???!!!!
Because the power supply is sell with an adaptor 2.1mm or 5.5mm. I want you explain that to me, because I'm not a professional in electronics.

-If I wan't to find the good connections on the back of the Dashboard, how can I do ? I should test with a multimeter?

I hope that my English isn't too bad.

Thanks a lot for the creation of Revburners !!!! And for the help you give to me.

Bye.

Pages: [1] 2
hit counter