Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - probuff

Pages: [1]
1
General Discussions / Re: REQUEST - Euro Truck Simulator 2
« on: July 29, 2016, 10:41:28 am »
Yes, i check'd it out and it work! thank You!
Moreover, is there any work arounds to activate relays w/ button press?

2
General Discussions / Re: REQUEST - Euro Truck Simulator 2
« on: July 27, 2016, 06:51:01 pm »
https://youtu.be/Ug3CbcrIXsI

Are there any news for acticating relays w/ buttons? hard to do ?

3
General Discussions / Re: REQUEST - Euro Truck Simulator 2
« on: July 17, 2016, 03:50:08 pm »


4
General Discussions / Re: REQUEST - Euro Truck Simulator 2
« on: June 29, 2016, 04:45:49 pm »
Just tried out and it seem not to work. Althou, hope you try it.
I jumped on LFS again to see if relays are still working, and they does.



I'm thinking I made a mistake for wiring up relays for turn/hazard signals, because they are available in only one game - LFS.
On the other hand most games I play is from this camera view.



Is there any chance to activate bulbs (make them blink) with some button press while there is no need for ingame function activation? (working externaly w/o game)
This would make turn signals available for everygame, because in most cases people wont bother of them working in a game

****I conneted them to JC32 and made them as buttons.



5
General Discussions / REQUEST - Euro Truck Simulator 2
« on: June 29, 2016, 07:10:41 am »
Hello community,
recently got Pro Gauge, Relay Controller and its module working.
Relay controller does magic for left/right turn, long lights bulbs.
It really works great on Live For Speed, as shown in picture below.


http://i.giphy.com/l2JIhiK3eJb1c1qUM.gif

Today I bought ETS2 expecting bulbs to do their job as well, but it does not.
ETS2 got left/right turn signals, long light signal, hazard signal.

Is there any chance to get software update to get these functions, please?
Or is there any way around for this?

Thank you!

6
Show off your build / Re: My cockpit build WIP
« on: December 15, 2015, 02:09:49 pm »
Ok,
I'm still trying them to work. I got progress of some sort on water temp gauge. When I connect everything water temp needle does not move. I take out blue connector while 12v is plugged and put it back in. Only then water temp need starts to respond. I did scaling right now, but still cannot figure out why it works this way. Fuel gauge seems to not respond at all (black connector - one wire speed, other fuel, thats it)

--
Ok, I'll continue, maybe somebody will find it useful. My Fuel Gauge did not respond at all. I changed the bulb of this gauge (it was not working) and Fuel Gauge needle become alive. Also, this sorted out the problem with Water gauge and I do not need to pull out/in blue connector to get it working. If your water temperature needle goes up to max and do not go down while calibrating, then you need to set 100% gauge scaling much lower, unplug usb/power and try again.

My last problem with this is Fuel Gauge. When I do scaling at certain number (126) it goes all the way up and gets stuck there. Lower numbers do not move the needle.

Any suggestions?

7
Show off your build / Re: My cockpit build WIP
« on: November 11, 2015, 11:37:11 am »


So yea guys,

According to this picture I connected all the wires, but still cant make fuel/temp gauges to work.
I'm not sure why, but +12v connection might be a problem -

White - all the +12 wires (3 of them) made to one.
Blue - all the +12 wires (3 of them) made to one.
Then I made extension connect all of them to one again (6 of them now) and one wire to pro gauge (12v) itself and another one to power supply.

Did I made a mistake connecting them this way?

I noticed that water temp sometimes goes up to random position and stays there.

Anyone faced this problem? Thanks:)

8
General Discussions / Re: Pro Gauge wiring
« on: August 30, 2015, 11:12:25 am »
Hey,
First - really great quality job you have done.
I got E36 dash too and wondering, what simproject boards did you use to make everything work?
I guess they are but different today and cant find same that you used.
Could somebody link me boards to buy to make everything work? I live in UK :)
Do I need two redburners or one progauge?

Thanks for reply!:)

Pages: [1]
hit counter