Show Posts

1

General Discussions / Re: JC32

« on: April 12, 2023, 01:42:51 pm »

video sent...

2

General Discussions / Re: JC32

« on: April 12, 2023, 01:17:11 pm »

thanks Christiano.

windows found the second jc32.
but i have a huge delay from ca. 1 sec.
in ets2 settings on my win 10 pc it will not work when i push the button for calibrating.

the Joystick Controller Configuration Utility will not save the settings

i have 3 usb cable testet.
and on my laptop is it the same.

jc32 number one (firmware 1.0) is all fine
jc32 number two (firmware 2.0) not working, delay and no save the settings.

thanks
Mitchell

3

General Discussions / JC32

« on: March 27, 2023, 10:09:04 am »

HI

is it possible to use two jc32 controllers at the same time? and how does the software react?

thanks
Mitchell

4

General Discussions / SimDash new feature?

« on: August 28, 2018, 02:51:49 pm »

@Cristiano

could you update your SimDash software so that when you open it sees what profile you have loaded? I currently use several profiles and it would be easier to directly see which profile is currently active.

Thank you
Mitchell

5

General Discussions / Re: JC-LED ... LED Voltage

« on: August 11, 2018, 12:05:58 pm »

ok, works fine

Mitchell

6

General Discussions / Re: JC-LED ... LED Voltage

« on: August 07, 2018, 04:48:32 pm »

i ordered now on amazon and will it testet

Mitchell

7

General Discussions / Re: JC-LED ... LED Voltage

« on: August 06, 2018, 10:19:28 am »

thanks Cristiano

here the link:

https://www.amazon.de/dp/B0788PTLX8/ref=cm_sw_r_cp_api_AfbABbDF99734

Mitchell

8

General Discussions / JC-LED ... LED Voltage

« on: August 06, 2018, 07:10:02 am »

Hi

what volts do the LEDs need to have for the jc-led board?

thanks
Mitchell

9

Questions about specific simulators / Re: FORZA MOTORSPORT 7 SUPPORT ?

« on: June 25, 2018, 12:43:41 pm »

Yes, Please!!!

10

General Discussions / Re: BMW E36 316 temp and fuel not working

« on: May 02, 2018, 08:35:56 pm »

Quote from: Mykoliuxas on May 02, 2018, 08:09:56 pm

So, connected fuel from Pin 1 (black connector) and water temp pin 18 (blue connector) to pro gauge, temperature went from 0 to max and nothing happens, and fuel gauge just stays at lowest position and nothing else happens, configured gauges like Mitchell did, still nothing. Im starting to give up with these two gauges. Any more suggestions?
Mykolas

I also had problems at the beginning

you must test from 0-4095 in 10 number steps. (10 . 20 . 30 etc)

set the 100% from the fuel gauge to 10, klick test and than you must your e36 cluster turn off and on. the needle does not work, then go to 20, than the e36 cluster off and on etc.

you have to be patient. It will take a while to set it right.

Mitchell

11

Show off your build / Re: My First Cockpit Build

« on: May 02, 2018, 07:09:30 pm »

Quote from: Mykoliuxas on May 02, 2018, 06:40:11 pm

Really nice build! I was wondering, what pins from cluster you used for water temp and fuel? Because i have Bmw 316 cluster, and can't make water temp and fuel gauges on cluster to work.
Thanks

Fuel gauge / pin 1 (black plug socket)
temp gauge / pin 18 (blue plug socket)

see the numbers of the cluster for the pin sequence.

Mitchell

12

General Discussions / Re: BMW E36 316 temp and fuel not working

« on: May 01, 2018, 06:49:27 pm »

Quote from: Mykoliuxas on May 01, 2018, 08:29:29 am

Hello, few weeks ago I received pro-gauge, really happy with it, connected it to BMW E36 316 cluster, speedometer and rpm works great, buut the temp and fuel gauge don't want to work. Tried configuring, tried configure with signal adapter - nothing. I've connected everything like in this pic I attached:
And I ran out of ideas. Maybe here are some people who could help me.
Thanks

here my bmw e36 318i gauge settings:

Mitchell

13