Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - mr.w

Pages: [1] 2 3 ... 5
General Discussions / looking to add some gauges to my dashboard
« on: July 13, 2017, 05:43:08 pm »
Been some time since I have done any sim racing but looking to get back into it and with that comes tinkering with my cockpit.  currently I have a progauge with tach, speedo, oil temp and water temp.  I have Project cars, Assetto Corsa and RFactor2 any other gauges you would recommend to add, I was thinking fuel level, oil pressure, turbo (Assetto/ boost or PSI?). any help would be great.  FYI i have the Dragon gauges for the water and temp currently.

General Discussions / Re: Monsta support for f1 2013 .
« on: December 31, 2013, 01:44:03 am »
anyone have an idea of what the settings are for the pro race LED shift lights want it to mirror the game.
any data for KERS and DRS from the game?

General Discussions / Re: Pro Gauge power question
« on: September 30, 2013, 06:39:12 pm »
wired and I can confirm all is working, 5 inch tach and 2 @ 2 inch gauge.

General Discussions / Re: Pro Gauge power question
« on: September 29, 2013, 07:06:49 pm »
so is that a yes for powering the Pro Gauge with a PC power supply?

General Discussions / Re: Toggle Switch and Pro Race wiring question
« on: September 29, 2013, 05:55:41 pm »
the switch did not come with any documentation.  currently i have it wired up with to the pro race with the ground and the positive, I have not attempted to wire it up any other way.
I could try to see what results i get.

General Discussions / Re: New Simscreen?
« on: September 28, 2013, 07:38:11 pm »
Cristiano, how far out are we looking at this project?

General Discussions / Toggle Switch and Pro Race wiring question
« on: September 24, 2013, 03:27:24 am »
So I have a Pro Race with the button adapter and a Toggle Switch

Can someone tell me how to wire this switch and supply power to the LED while still having the switch work with the Pro Race button portion of the board (when the switch is in the "on" position it represents a button press)

My last attempt at asking this was not helpful to me ( my fault wiring and electronic not my strong point) and I believe the people on this forum were trying to set up the switch as a supply power (on) no power (off).

General Discussions / Re: My custom gauge WIP (shaun_king)
« on: July 28, 2013, 06:46:03 pm »
any issues with changing the values on the gauges, I noticed that you changed the RPM to 1200 max vs what they were stock?  I have a pair of Civic gauges and would like to add to the RPMs from 9000 to maybe 1200. not sure if going up will cause any issues or is it all in the way you configure it in the software.

General Discussions / Re: How many gauges
« on: July 20, 2013, 07:41:27 pm »
did I read somewhere in this form that you can use a pc power supply and connect them to the terminals on the board and run it that way?

General Discussions / Re: Pro Race and button adapter wiring question
« on: June 05, 2013, 03:25:29 am »
boy I am getting in over my head i think, Sorry H.Guedes, that didnt help at all. cant figure out your scheme, I guess my question would be if I wire up my switch the way Jarden suggests with a separate power source for the light.

General Discussions / Re: Pro Race and button adapter wiring question
« on: June 04, 2013, 08:46:30 pm »
OK so what I can understand is that I wire up the switch as I would a button and add a separate 12 volt source to the "+" terminal and have the ground from that 12 volt source ground elsewhere

Show off your build / Re: My WIP dashboard / cockpit
« on: June 03, 2013, 07:28:57 pm »
What wheel are you planning on using in your cockpit?

General Discussions / Re: Pro Race and button adapter wiring question
« on: June 03, 2013, 07:27:18 pm »
Here is sheme how to connect


I figured that much but I wanted to know in relation to the Pro Race/button adapter, is there 12volt on the board.  Ideally I would like to be able to use this switch as a On/Off switch and have the light turn off and on. so as a basic toggle, but the switch itself requires voltage to power the light correct?

General Discussions / Pro Race and button adapter wiring question
« on: June 02, 2013, 04:55:07 pm »
I have received my Pro Race and from what I can see everything is working, but my question fals on the button adaptor and a safety toggle switch that I have, the switch is from ebay

my question is there a way to wire up the switch and have the LED work at the same time with the pro race, I believe the last time I tried to wire this switch up with a Leo board I fried a portion of the board.

Pages: [1] 2 3 ... 5
hit counter