Author Topic: 5" Proparts SPEK Tach wiring HELP  (Read 8518 times)

r0gu3

  • Approved Newbie
  • *
  • Posts: 12
    • View Profile
5" Proparts SPEK Tach wiring HELP
« on: June 27, 2013, 09:38:57 am »
Hi Guys, I have a problem where the Proparts SPEK  11,000 rpm tach, it does not want to go over 8800 rpm, when I set the max rpm in the progauge software,
 Do I need to wire the White(dimmer) to the 12V ?
I haven't connected the the white wire (dimmer) only the green to rpm - red to 12V and Black to ground
I've been hearing about changing to 8 cylinder how do I do that please :)
« Last Edit: June 27, 2013, 09:48:41 am by r0gu3 »

H.Guedes

  • Jr. Member
  • **
  • Posts: 73
    • View Profile
Re: 5" Proparts SPEK Tach wiring HELP
« Reply #1 on: June 27, 2013, 01:05:41 pm »
If i'm not wrong the revburner works the same way that progauge.

4 cylinders engine rev counters up to 17.000 RPM
6 cylinders engine rev counters up to 12.000 RPM
and 8 cylinders engine rev counters up to 8.000 RPM

But i remember read somewhere the proparts spek gauge have some issues to work. (but i can't be precise with that information)

Cristiano

  • Administrator
  • Hero Member
  • *****
  • Posts: 1360
    • View Profile
    • SymProjects
    • Email
Re: 5" Proparts SPEK Tach wiring HELP
« Reply #2 on: June 27, 2013, 05:48:26 pm »
Hi.
you should check the documentation that comes with your rev counter and see if you can set the number of cylinders of the engine.
usually the choise is between 4, 6 or 8 cylinders.

Choose 4 or 6. if number of cylinders is set to 8, you don't get more than 8.000 RPM

Regards
Cristiano


Hi Guys, I have a problem where the Proparts SPEK  11,000 rpm tach, it does not want to go over 8800 rpm, when I set the max rpm in the progauge software,
 Do I need to wire the White(dimmer) to the 12V ?
I haven't connected the the white wire (dimmer) only the green to rpm - red to 12V and Black to ground
I've been hearing about changing to 8 cylinder how do I do that please :)

mikeperry

  • Approved Newbie
  • *
  • Posts: 45
    • View Profile
Re: 5" Proparts SPEK Tach wiring HELP
« Reply #3 on: June 28, 2013, 08:57:50 am »
YOu need to supply 12V to the White wire, that is the only way to program the PPM mode which you need to set the Needle to 1000 in the spek Tach. If you have the Directions to the Tach then it will tell you how to do this. If not I can send you the directions.

mikeperry

  • Approved Newbie
  • *
  • Posts: 45
    • View Profile
Re: 5" Proparts SPEK Tach wiring HELP
« Reply #4 on: June 28, 2013, 08:58:54 am »
If i'm not wrong the revburner works the same way that progauge.

4 cylinders engine rev counters up to 17.000 RPM
6 cylinders engine rev counters up to 12.000 RPM
and 8 cylinders engine rev counters up to 8.000 RPM

But i remember read somewhere the proparts spek gauge have some issues to work. (but i can't be precise with that information)


The Spek tachs work perfectly with Symprojects products.

r0gu3

  • Approved Newbie
  • *
  • Posts: 12
    • View Profile
Re: 5" Proparts SPEK Tach wiring HELP
« Reply #5 on: June 28, 2013, 04:55:32 pm »
Yup yup. thank you everyone. Yes I wired the white (dimmer) to the 12V and hold the middle and top button for 5 second and then PRess the centre button once to get into the PPR setting. and I changed it to 1000 and works perfectly.

thank you so much. guys. sorry for the late reply. spent 4 hours and didn't realize I have to press the centre button after the 5 second hold. the manual didn't state or I missed it some how. lol
 ;D

 

hit counter