SymProjects Forum
General Category => General Discussions => Topic started by: Nick05 on October 09, 2013, 07:38:38 pm
-
Hi all,
Just purchased a JC32 Joystick Controller along with some rotary switches and push button switches (thanks for speedy delivery btw ;) ) and I would like to add some toggle switches which leads me on to my question.......
what volt / amp specs should the toggles be ? I know I need spst on/off but there are so many different volt amp types I am a bit lost ::)
Thanks in advance,
Nick.
-
hi.
there is virtually no current flowing through the switch that any switch will work fine.
you can double check here what you will decide to buy, and I will confirm that it will work.
Regards
Cristiano
Hi all,
Just purchased a JC32 Joystick Controller along with some rotary switches and push button switches (thanks for speedy delivery btw ;) ) and I would like to add some toggle switches which leads me on to my question.......
what volt / amp specs should the toggles be ? I know I need spst on/off but there are so many different volt amp types I am a bit lost ::)
Thanks in advance,
Nick.
-
Hi Cristiano, Thank you for your reply...........
I would like to be able to use these ones http://www.ebay.co.uk/itm/271104191854?var=570127019605&ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649 (http://www.ebay.co.uk/itm/271104191854?var=570127019605&ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649)
Will they be ok ?
-
I think it will work but I am not sure about the LED.
the LED works at 12V but the JC32 only has 5V
Hi Cristiano, Thank you for your reply...........
I would like to be able to use these ones http://www.ebay.co.uk/itm/271104191854?var=570127019605&ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649 (http://www.ebay.co.uk/itm/271104191854?var=570127019605&ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649)
Will they be ok ?
-
I managed to nip into town and grab some, I have them installed and although the LED's are lighting up when the switch is toggled to "ON" but the switch itself is not registering ?
I have them wired correctly and also the correct switch numbers are assigned in the "Toggle switch" configuration menu and I am also using the debug option but cant seem to get the switch itself to work ?
-
are you sure they are wired correctly. do they come with any documentation?
can you describe the pins and how they are connected?
I managed to nip into town and grab some, I have them installed and although the LED's are lighting up when the switch is toggled to "ON" but the switch itself is not registering ?
I have them wired correctly and also the correct switch numbers are assigned in the "Toggle switch" configuration menu and I am also using the debug option but cant seem to get the switch itself to work ?
-
Thought it would be easier to draw a pic rather than explain :P
-
Probably that + and - is for the Led no? try use instead the - and acc. Because this switch have the common ground ( for the switch and the led). But it's hard to say because i dont know that for sure. (My switch works this way i told you)
-
Probably that + and - is for the Led no? try use instead the - and acc. Because this switch have the common ground ( for the switch and the led). But it's hard to say because i dont know that for sure. (My switch works this way i told you)
Hi,
I tried your suggestion but still no luck, with your configuration the LED stays on constant, with the way I had it in the diagram the LED only comes on when the switch is toggled to ON ???
-
The ebay link in the topic is the same of the switch you have? I will try discover how they work and tell you something
-
The ebay link in the topic is the same of the switch you have? I will try discover how they work and tell you something
Yes they are exactly the same, Thank you for your help, its much appreciated ;)
-
Well in my haste to get these toggles working I have some how manage to fry one side of my controller >:( (If I plug a switch into said side I get nothing, if I plug that same switch into the other side it works)
Cristiano do you offer some kind of repair service or do I need to buy a new one ?
-
Please send me an email at contact@symprojects.com
Well in my haste to get these toggles working I have some how manage to fry one side of my controller >:( (If I plug a switch into said side I get nothing, if I plug that same switch into the other side it works)
Cristiano do you offer some kind of repair service or do I need to buy a new one ?