1
General Discussions / Re: MY Symprojects Homemade Dashboard
« on: October 28, 2016, 09:49:41 am »
Price lowered: 200€+SHIPPING
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
General Discussions / Re: MY Symprojects Homemade Dashboard
« on: September 09, 2016, 10:28:30 am »
I ship the board as it is on the pictures. Fully build and connected and already assembled on the 4 boards. I can also send my configuration file or help setup the board via mail or skype. The board is fully functional and ready to go. The board is powered by the usb cables no external power supply required.
All new it was aprox. £400 or in my case 475€ without shipping and work. I hope to sell it for 290€ (or £250 + shipping).
You can contact me by PM or lorencic.david@hotmail.com for more pictures or questions
All new it was aprox. £400 or in my case 475€ without shipping and work. I hope to sell it for 290€ (or £250 + shipping).
You can contact me by PM or lorencic.david@hotmail.com for more pictures or questions
3
General Discussions / Re: MY Symprojects Homemade Dashboard
« on: September 09, 2016, 10:13:58 am »
THIRD BOARD(aka. BUTTON BOARD)
The buttons:
- Lights (above the button is a Blue LED to show that the lights are on)
- Wipers (above the button is a Blue LED to show that the wipers are on)
- Request Pit Stop (above the button is a Green LED to show that you requested a pit stop)
- Pit Speed Limiter (above the button is a Green LED to show that you pit limiter is ON)
- Engine Contact (above the button is a Red LED to show engine contact)
- Start Engine
- Rotary encoder for setting(Wing, ARB, etc.)
- there are 2 LED's left of the rotary encoder that show 1x You are in the pits and 1x Red LED Engine Fail
Displays:
- Cars on track(3 digit display)
- My position ( 3 digit display)
- Turbo Pressure (3 digit display)
Under all the buttons is still space for a sim-screen ss1 just never made the hole and put it in.
FOURTH BOARD(aka. PIT BOARD)
THE BUTTONS:
- ROTARY ENCODER for setting Brake Bias ( front or back)
- ROTARY ENCODER for setting Boost (low to high)
- Button for Launch Control
- Button for FFB reset
- Button for YES
- Button for NO
- Button for CHAT
- PIT buttons UP, DOWN, INCREASE, DECREASE and CONFIRM
LED's:
- Traction Control
- ABS
- Fuel Prssure (3 LED's Green, Yellow, Red)
- Water Temp Warning
- Oil Temp Warning
- Fuel Pressure Warning
The buttons:
- Lights (above the button is a Blue LED to show that the lights are on)
- Wipers (above the button is a Blue LED to show that the wipers are on)
- Request Pit Stop (above the button is a Green LED to show that you requested a pit stop)
- Pit Speed Limiter (above the button is a Green LED to show that you pit limiter is ON)
- Engine Contact (above the button is a Red LED to show engine contact)
- Start Engine
- Rotary encoder for setting(Wing, ARB, etc.)
- there are 2 LED's left of the rotary encoder that show 1x You are in the pits and 1x Red LED Engine Fail
Displays:
- Cars on track(3 digit display)
- My position ( 3 digit display)
- Turbo Pressure (3 digit display)
Under all the buttons is still space for a sim-screen ss1 just never made the hole and put it in.
FOURTH BOARD(aka. PIT BOARD)
THE BUTTONS:
- ROTARY ENCODER for setting Brake Bias ( front or back)
- ROTARY ENCODER for setting Boost (low to high)
- Button for Launch Control
- Button for FFB reset
- Button for YES
- Button for NO
- Button for CHAT
- PIT buttons UP, DOWN, INCREASE, DECREASE and CONFIRM
LED's:
- Traction Control
- ABS
- Fuel Prssure (3 LED's Green, Yellow, Red)
- Water Temp Warning
- Oil Temp Warning
- Fuel Pressure Warning
4
General Discussions / Re: MY Symprojects Homemade Dashboard
« on: September 09, 2016, 10:02:25 am »
The parameters I used:
FIRST BOARD(aka. SETUP BOARD):
- Fuel(Liters) ( 3-digit display)
- Oil Temp(°C) ( 3-digit display)
- Water Temp(°C) ( 3-digit display)
- Led's for FLAGS (Green flag, Blue flag, Red flag, Yellow flag 3 LED's for each sector)
- Brake Temp(3 LED's for each wheel (blue, yellow and red in °C)
- Wheel Temp(3 LED's for each wheel (blue, green and red in °C)
SECOND BOARD(aka. MAIN BOARD):
- Water Temperature (5 LED's 2xBlue, 1xYellow, 1xGreen, 1xRed)
- Oil Temperature (5 LED's 2xBlue, 1xYellow, 1xGreen, 1xRed)
- RPM Meter(4 Green LED's,6 Red LED's and 4 Blue LED's)
- Speed(3 digit display)
- Gear(1 digit display)
- Last lap time(6 digit display)
- Fuel (1 Red LED, 2 Yellow LED's, 3 Green LED's)
FIRST BOARD(aka. SETUP BOARD):
- Fuel(Liters) ( 3-digit display)
- Oil Temp(°C) ( 3-digit display)
- Water Temp(°C) ( 3-digit display)
- Led's for FLAGS (Green flag, Blue flag, Red flag, Yellow flag 3 LED's for each sector)
- Brake Temp(3 LED's for each wheel (blue, yellow and red in °C)
- Wheel Temp(3 LED's for each wheel (blue, green and red in °C)
SECOND BOARD(aka. MAIN BOARD):
- Water Temperature (5 LED's 2xBlue, 1xYellow, 1xGreen, 1xRed)
- Oil Temperature (5 LED's 2xBlue, 1xYellow, 1xGreen, 1xRed)
- RPM Meter(4 Green LED's,6 Red LED's and 4 Blue LED's)
- Speed(3 digit display)
- Gear(1 digit display)
- Last lap time(6 digit display)
- Fuel (1 Red LED, 2 Yellow LED's, 3 Green LED's)
5
General Discussions / MY Symprojects Homemade Dashboard
« on: September 09, 2016, 09:25:10 am »
Hello. I'm selling my homemade dashboard, recently I have quit online racing so I don't need it anymore.
The board consist of(READ: what you get):
- 2x DLC247 (£99 GBP)
- 1x JC32 Joystick controller (£25.50)
- 6x DLC247 pin-splitter (£15.00)
- 7x 0.56" Three digit display for DLC-247 (£41.65)
- 1x 0.36" Six digit display for DLC-247 (£6.95)
- 1x 0.56" display for DLC-247 (£5.95)
- 75 5mm Leds (£7.50)
- 16 Push Buttons (aprox. £15.00)
- 3x Rotary Encoder (£11.85)
- 3 usb cables to connect to the PC (aprox. £6.00)
- 4 aluminium boards with machined holes and painted in black (aprox. £150)
The board consist of(READ: what you get):
- 2x DLC247 (£99 GBP)
- 1x JC32 Joystick controller (£25.50)
- 6x DLC247 pin-splitter (£15.00)
- 7x 0.56" Three digit display for DLC-247 (£41.65)
- 1x 0.36" Six digit display for DLC-247 (£6.95)
- 1x 0.56" display for DLC-247 (£5.95)
- 75 5mm Leds (£7.50)
- 16 Push Buttons (aprox. £15.00)
- 3x Rotary Encoder (£11.85)
- 3 usb cables to connect to the PC (aprox. £6.00)
- 4 aluminium boards with machined holes and painted in black (aprox. £150)
6
General Discussions / Re: suport for MONSTA for f1 2015
« on: July 13, 2015, 10:33:30 am »
Cristiano is working on a update he will release it soon...
7
General Discussions / Re: New and dlc247 help
« on: June 10, 2015, 06:56:32 pm »
yes you can...you configure each digit seperatley...
8
General Discussions / Re: New and dlc247 help
« on: June 09, 2015, 07:55:19 am »
hey...i will try to answer some of the questions...
if you want to run 4 six digit displays and 4 three digit displays you need 1 dlc 247 and 3 pin splitters...then you need a second dlc for the light array...and other stuff you want to add.
for the gears I'm not sure but i think you can link together 2 1digit displays...and you can get to ex. 16 gear...someone who drives ETS2 should correct me on this.
how do you mean values for the shift light array? you put in % for each led when it lights up...example: you have 10 leds every next led turns on 10%-20%-30% etc. 100%...but only if the sim supports rpm in %...
if you want to run 4 six digit displays and 4 three digit displays you need 1 dlc 247 and 3 pin splitters...then you need a second dlc for the light array...and other stuff you want to add.
for the gears I'm not sure but i think you can link together 2 1digit displays...and you can get to ex. 16 gear...someone who drives ETS2 should correct me on this.
how do you mean values for the shift light array? you put in % for each led when it lights up...example: you have 10 leds every next led turns on 10%-20%-30% etc. 100%...but only if the sim supports rpm in %...
9
General Discussions / Re: Has support ended?
« on: May 29, 2015, 06:51:28 pm »
I hope Cristiano will release the source code to simdash before he abandons his project....
10
General Discussions / Problem with DLC247
« on: May 06, 2015, 09:12:23 am »
Hello, i have a problem with my board...when i have it set to power through the DC power supply the led's and displays don't work. When i set it to power through USB everything works normal. Does that mean that the DC power supply is faulty?
Greets, David.
Greets, David.
11
General Discussions / Re: DLC-247 not recognized - "can not be started"
« on: December 16, 2014, 05:04:46 pm »
I found a fix for the problem! Plug in the device and let it fail to install. Then go to My Computer and right click on it then select Properties. On the top you will se Device Manager. When you have it open select the device right click on it and select Properties. Select the third tab Driver. Then go Update Driver. Select Browse my computer for driver software. Next you must select Let me pick from a list of device drivers on my computer. There will be 2, select the first one and click Next. THE DLC-247 NOW WORKS AGAIN. 
If anyone has trouble I'll be glad to help.
David.
If anyone has trouble I'll be glad to help.
David.
12
General Discussions / Re: DLC-247 not recognized - "can not be started"
« on: December 07, 2014, 08:19:06 pm »
Can anyone specify the update number? ex. KBxxxxxx? thanks in advance.
David.
David.
13
General Discussions / Re: PLEASE HELP!!!!!!!
« on: October 12, 2014, 09:13:44 am »
If you post a picture of the DEPO gauge(back side, where the wires are) maybe we can help you.
Cheers, David.
Cheers, David.
14
General Discussions / Re: Assetto Corsa Support
« on: January 06, 2014, 10:50:32 am »
I just want to share a link for Cristiano!
https://docs.google.com/document/d/13trBp6K1TjWbToUQs_nfFsB291-zVJzRZCNaTYt4Dzc/pub
here are some parameters than can be exported from AC...hope you find this helpfull.
Greets, David!
https://docs.google.com/document/d/13trBp6K1TjWbToUQs_nfFsB291-zVJzRZCNaTYt4Dzc/pub
here are some parameters than can be exported from AC...hope you find this helpfull.
Greets, David!
15
General Discussions / Re: Rev Lights Configuration
« on: November 29, 2013, 09:45:04 pm »
I know how to configure the LEDS, but I don't know the best settings or if someone has already configured the % for the revs for 14 LEDs.
or if someone has already configured the % for the revs for 14 LEDs.
