1
Questions about specific simulators / Re: Where do we stand on Project Cars 2?
« on: September 24, 2017, 10:28:02 am »
any updates on it?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
General Discussions / Re: Grid Auto Sport support
« on: October 02, 2014, 07:35:45 am »
i have found an very good walkaround and it works:
here the site where i found this
http://www.siminstruments.com/software/setup.txt
To get Grid Autosport to work:
Open the file C:\Users\[james]\Documents\My GamesGRID Autosport\hardwaresettings\hardware_settings_config.xml in notepad.
Changing [james] with our windows login name.
Update the line near the end that starts with "<motion" to look the same as below;
<motion enabled="true" ip="127.0.0.1" port="20777" delay="1" extradata="3" />
If you are running other software, fanaleds, simxperience, you can customise the port used above.
The the following files;
Grid Autosport - 513b39d5-dbc8-4906-8857-71217baaa211_plugIn.xaml
The should now be these three options; PortIn="20777" PortOut="20778" ExtraDataOut="2"
Change the portin to the port you want Siminstruments to read data from, and then PortOut to the port you want Siminstruments to send data to.
ExtraDataOut, to get the most out of Codemasters telemetery data it is best to have the game set to ExtraDataOut="3" for Siminstruments software. If you have other software that can only handle ExtraDataOut="2" then set them to pick up data from the PortOut with ExtraDataOut set to 2 in the above _plugIn.xaml.
here the site where i found this
http://www.siminstruments.com/software/setup.txt
To get Grid Autosport to work:
Open the file C:\Users\[james]\Documents\My GamesGRID Autosport\hardwaresettings\hardware_settings_config.xml in notepad.
Changing [james] with our windows login name.
Update the line near the end that starts with "<motion" to look the same as below;
<motion enabled="true" ip="127.0.0.1" port="20777" delay="1" extradata="3" />
If you are running other software, fanaleds, simxperience, you can customise the port used above.
The the following files;
Grid Autosport - 513b39d5-dbc8-4906-8857-71217baaa211_plugIn.xaml
The should now be these three options; PortIn="20777" PortOut="20778" ExtraDataOut="2"
Change the portin to the port you want Siminstruments to read data from, and then PortOut to the port you want Siminstruments to send data to.
ExtraDataOut, to get the most out of Codemasters telemetery data it is best to have the game set to ExtraDataOut="3" for Siminstruments software. If you have other software that can only handle ExtraDataOut="2" then set them to pick up data from the PortOut with ExtraDataOut set to 2 in the above _plugIn.xaml.
3
General Discussions / Re: Grid Auto Sport support
« on: October 01, 2014, 02:17:59 pm »
is anybody here who can helps?
4
General Discussions / Re: gauge values different after changing Pro-Gauge power supply to ATX
« on: October 01, 2014, 02:16:37 pm »
Hi!
i have the problem that my fuel and water temps not working on the bmw cluster with the pro-gauge power cable.
can you say me your settings in sim dash?
i have the problem that my fuel and water temps not working on the bmw cluster with the pro-gauge power cable.
can you say me your settings in sim dash?
5
General Discussions / Re: Grid Auto Sport support
« on: September 30, 2014, 07:30:23 pm »
i need help in this case.
i use an pro-gauge and pro-shift
i cant use grid autosport.
i dont understand the walkaround with the f1 2013 exe
can everybody help me???
i use an pro-gauge and pro-shift
i cant use grid autosport.
i dont understand the walkaround with the f1 2013 exe
can everybody help me???
6
General Discussions / Re: new project help needed
« on: December 09, 2013, 03:27:19 pm »
only i can send an pic from the gamepad pcb
i will know on which contacts i must pin the shifter lines for up, down and ground
i will know on which contacts i must pin the shifter lines for up, down and ground
7
General Discussions / Re: new project help needed
« on: December 09, 2013, 10:46:38 am »
no i use the 12v power supply that comes with the pro-gauge.
yesterday i have install all cables and have started the test.
speed and rpm works fine, but the fuel and water temps dosnt work.
today i will check these two connections.
so today i will connect an bmw E39 steptronic shifter to an usb gamepad controller. my problem-> i dont know which contacts i need on the gamepad ^^
yesterday i have install all cables and have started the test.
speed and rpm works fine, but the fuel and water temps dosnt work.
today i will check these two connections.
so today i will connect an bmw E39 steptronic shifter to an usb gamepad controller. my problem-> i dont know which contacts i need on the gamepad ^^
8
General Discussions / Re: new project help needed
« on: December 05, 2013, 09:45:39 pm »
ok it looks that i must connect 3x +12V Pins from white and all 3 pins +12v from blue to the pro gauge power port
9
General Discussions / Re: new project help needed
« on: December 05, 2013, 07:42:57 am »
so today the cluster and the progauge has arrived. now i will buy some cables for the wirring.
here is the problem for me....the wirring
can you check my wires and tell me if i have an wrong wirring?
so, i have the white, blue and black conector
pin 2 +12v on white con. goes to the +12v on the progauge
pin 19 GND on white con. goes to the GND on progauge
pin 20 RPM Sensor on white con. goes to RPM port on progauge
What is with the +12v (30) and (15) on the white con?
next is the blue conector:
i dont know what i have to conecting ... +12v(15) +12v(R) GND???
next is the black conector:
pin 3 GND to progauges GND?
pin 4 Speed Sensor to speed port on progauge
what pins i need for oil/water temps and for fuel level???
can you say me, how is the wirring for the leds??
here is the problem for me....the wirring
can you check my wires and tell me if i have an wrong wirring?
so, i have the white, blue and black conector
pin 2 +12v on white con. goes to the +12v on the progauge
pin 19 GND on white con. goes to the GND on progauge
pin 20 RPM Sensor on white con. goes to RPM port on progauge
What is with the +12v (30) and (15) on the white con?
next is the blue conector:
i dont know what i have to conecting ... +12v(15) +12v(R) GND???
next is the black conector:
pin 3 GND to progauges GND?
pin 4 Speed Sensor to speed port on progauge
what pins i need for oil/water temps and for fuel level???
can you say me, how is the wirring for the leds??
10
General Discussions / Re: new project help needed
« on: November 27, 2013, 07:33:38 am »
thanks paulie!!
i have ordered the pro-gauge yesterday.
can you give me an wirering diagram for an bmw e36 cluster?
i am an noob an have no idea to conect them to the cluster.
i have ordered the pro-gauge yesterday.
can you give me an wirering diagram for an bmw e36 cluster?
i am an noob an have no idea to conect them to the cluster.
11
General Discussions / new project help needed
« on: November 22, 2013, 10:59:47 am »
hey guys!
i need your help.
i will order an pro-gauge an will conect them to an BMW E36 Dashboard.
i play race07 and i dont know, what data race07 can give out to the dash.
i will use speed, rpm, oil temp an fuel level
what data can race07 give out?
does the pro-gauge work with race07?
i need your help.
i will order an pro-gauge an will conect them to an BMW E36 Dashboard.
i play race07 and i dont know, what data race07 can give out to the dash.
i will use speed, rpm, oil temp an fuel level
what data can race07 give out?
does the pro-gauge work with race07?
Pages: [1]
