« previous next »
Pages: [1]

Author Topic: Rotary encoder shaft size  (Read 22408 times)

ItsDaPlumber

  • Approved Newbie
  • *
  • Posts: 49
    • View Profile
Rotary encoder shaft size
« on: August 26, 2013, 04:01:20 pm »
Was wondering what size hole i need for the shaft of the rotary encoder.
Logged

r0gu3

  • Approved Newbie
  • *
  • Posts: 12
    • View Profile
Re: Rotary encoder shaft size
« Reply #1 on: August 27, 2013, 05:01:28 am »
most rotary encoder from ebay ( the one with blue base http://www.ebay.com.au/itm/10pcs-12mm-Rotary-Encoder-Switch-with-Keyswitch-New-/110706468028?pt=AU_B_I_Electrical_Test_Equipment&hash=item19c69ea4bc&_uhb=1) a 7mm hole should be enough, but they are a pain to wire because the distance between each pins are very close and they don' t have the best feel. price though can't be beaten

The one from leo bodnar or CTS branded ones, have a much nicer in quality and feel , and the hole size is 9.7mm or 10mm, it's easy to solder and wire, cons: Price.

I used both, the ebay ones are ok for volume chat, spotter, black box etc, but for bias knob , since I want to feel distinct notch each turn in Bias, I used CTS one.
Logged

ItsDaPlumber

  • Approved Newbie
  • *
  • Posts: 49
    • View Profile
Re: Rotary encoder shaft size
« Reply #2 on: August 27, 2013, 05:11:12 am »
Your the man!!! Thanks for the info. So, what am i looking for inperticular when looking for a rotary encoder? 16 detents? 20 detents? 4 bit or 2 bit? Can i use an illuminated rotary encoder?
Logged

Cristiano

  • Administrator
  • Hero Member
  • *****
  • Posts: 1360
    • View Profile
    • SymProjects
    • Email
Re: Rotary encoder shaft size
« Reply #3 on: August 27, 2013, 02:34:06 pm »
diameter of the shaft is 6mm, so I would make a 8-9 mm hole.



Quote from: ItsDaPlumber on August 26, 2013, 04:01:20 pm
Was wondering what size hole i need for the shaft of the rotary encoder.
Logged

r0gu3

  • Approved Newbie
  • *
  • Posts: 12
    • View Profile
Re: Rotary encoder shaft size
« Reply #4 on: August 30, 2013, 07:06:37 am »
Quote from: ItsDaPlumber on August 27, 2013, 05:11:12 am
Your the man!!! Thanks for the info. So, what am i looking for inperticular when looking for a rotary encoder? 16 detents? 20 detents? 4 bit or 2 bit? Can i use an illuminated rotary encoder?

no worries :)
16 Dents or 20 dents per revolution all works well, Im not sure if I have seen illuminated encoders before. so I'm not sure if the led from the encoders can be wired into the PCB, it should work, but I can never get the led  of my toggle switch to work properly when switch on so I ended up not wiring it . 
Logged

Mortos

  • Jr. Member
  • **
  • Posts: 80
    • View Profile
Re: Rotary encoder shaft size
« Reply #5 on: August 30, 2013, 01:06:22 pm »
Quote from: ItsDaPlumber on August 27, 2013, 05:11:12 am
Can i use an illuminated rotary encoder?

Yes. The LED/Illumination portion should be separate from the actual encoder. You can connect this to a DLC247 as an indicator, or to the power output from a Pro Gauge, if you use a resistor to limit current, to have it permanently lit.
Logged

ItsDaPlumber

  • Approved Newbie
  • *
  • Posts: 49
    • View Profile
Re: Rotary encoder shaft size
« Reply #6 on: August 31, 2013, 03:13:47 pm »
Well im not sure if anyone make an illuminated push button switch. I can use a toggle switch for the Mic Mute. I can find those that light up.

Darren
Logged
Pages: [1]
« previous next »
 

hit counter