Rev burner can't get top speed in speedo meter

[questerymj]

I maket his thread to prevent Cristiano miss my question.

http://www.symprojects.com/forum/index.php?topic=442.0

Even I drag the pulse to maxinum(67184) in simdash test mode only can drive my speedo meter to 80 km/h(max 180 km/h in speedo meter). How do I get rev burner to drive it to full range?

[Cristiano]

Problem is the rev burner can't generate pulses as quickly as the dashboard needs.

Tomorrow I am going to send you a new firmware. I don't know if it will work but it is worth trying.
Today I don't have the time sorry.

Speak tomorrow.

Cristiano

[questerymj]

Thank you Cristiano! Wait for your new firmware.

[Cristiano]

Here it is:

http://dl.dropbox.com/u/3544050/firmware.rar

I don't know if it will work, I couldn't test it.

[questerymj]

Cristiano, IT'S GREAT!:D:D:D:D

Now 67164 can drive the speedo meter to 165km/h(maxinum is 180 km/h).
Can you change the firmware a little more to make it to fill the full range?

[Cristiano]

try this one:

http://dl.dropbox.com/u/3544050/RevB.rar

If you are lucky you will be able to reach 180 Km/h but if you push it too high there is a possibility that SimDash freezes.

Regards
Cristiano

[perkabrod]

Is it possible to order a custom firmware?
I just posted in the Nissan S13 about a guy who made a frequency converter to make his Nissan S14 cluster work on the S13.
I didn't get half of it when he talked about the waves and stuff but if you have a read maybe you could give answer or offer me a firmware for my revburner speedo

[Cristiano]

Is it possible to order a custom firmware?
I just posted in the Nissan S13 about a guy who made a frequency converter to make his Nissan S14 cluster work on the S13.
I didn't get half of it when he talked about the waves and stuff but if you have a read maybe you could give answer or offer me a firmware for my revburner speedo

Hi.

Do you have a link to the discussion of the guy who make the frequency converter?

Thanks
Cristiano

[questerymj]

Thank you Cristiano!

Now rev burner can drive my speedo to max in only 36600. I just need to deal with the gear position indicator LEDs ( can'r light them by Pro shift, maybe need higher voltages. Normal LEDs works with Pro shift) and i will get a perfect result I dream of.

Thanks for your great customer service and making ourracing life more joyful!

[Cristiano]

Thank you Cristiano!

Now rev burner can drive my speedo to max in only 36600. I just need to deal with the gear position indicator LEDs ( can'r light them by Pro shift, maybe need higher voltages. Normal LEDs works with Pro shift) and i will get a perfect result I dream of.

Thanks for your great customer service and making ourracing life more joyful!

What LEDs are you trying to use for the gear position?

[perkabrod]

Do you have a link to the discussion of the guy who make the frequency converter?

Yes, actually just noticed it was for S15 but anyway... the build is here, hope you find it interesting:
http://www.freshalloy.com/forums/showthread.php?t=179595

[questerymj]

What LEDs are you trying to use for the gear position?

There are already 6 gear indicator LEDs soldered in the cluster PCB board. They are big ones (maybe 8mm I guess) and not the removable bulbs been used on other lamps/indicator. So I check the circuit and try to light them directly from harness connector legs (they are connect to gear position switch directly, not MCU) but failed.

Because these LEDs are shared negative, I think the best way is remove them and soldner some 5mm LEDs( fit to pro shift) with polarity opposite. Will test this when I have time:)

[Cristiano]

What LEDs are you trying to use for the gear position?

There are already 6 gear indicator LEDs soldered in the cluster PCB board. They are big ones (maybe 8mm I guess) and not the removable bulbs been used on other lamps/indicator. So I check the circuit and try to light them directly from harness connector legs (they are connect to gear position switch directly, not MCU) but failed.

Because these LEDs are shared negative, I think the best way is remove them and soldner some 5mm LEDs( fit to pro shift) with polarity opposite. Will test this when I have time:)

the LEDs connected to the Pro Shift share the positive...

[questerymj]

Yes, but the leds on cluster PCB share negative...so I decide to dissolder them , change to normal 5mm leds with opposite polarity them they share positive.

[questerymj]

I dissolder all gear position indicator leds and isolate the circuit...the result is nice.

http://www.youtube.com/watch?v=Inr8_2nQk4A&feature=youtu.be