Author Topic: how do i get the rev burner to tell me when to change gear (Read 30632 times)

jaykop · « **on:** November 22, 2012, 08:25:56 pm »

how do i get the rev burner to tell me when to change gear as the red led on my tacho is not coming on when I do the test on sim dash can anyone advise or do I need to use the led from my pro shift to get it working on the tacho ......

Uploaded with ImageShack.us

Cristiano · « **Reply #1 on:** November 23, 2012, 10:41:22 am »

Hi.
The LED on you tachometer is not driven by the rev burner. it's the tachometer that decides when to turn it on.
Usually there is a know on the tacho to set the RPM value at which the LED turns on. Or buttons.

Regards
Cristiano

jaykop · « **Reply #2 on:** November 23, 2012, 10:47:35 am »

When I plug in the tachometer and do the test when it goes to the red part 9 10 11 when the red light supposed to come it doesn't the led has a black and red wire do I just connect them to the + and the - please advise me thanx....

Cristiano · « **Reply #3 on:** November 23, 2012, 10:53:46 am »

As I said it depends on the tachometer.
Does the tachometer have any button near the LED? in the picture it is not clear

jaykop · « **Reply #4 on:** November 23, 2012, 10:57:23 am »

Yes it has a mode button and a arrow up and down buttons ...... and on the back it had a 4 6 8 switch on the back ....

Cristiano · « **Reply #5 on:** November 23, 2012, 11:02:43 am »

You have to use the MODE and ARROW UP and ARROW DOWN buttons to set the shift light.
Did the tachometer come with any instructions?

jaykop · « **Reply #6 on:** November 23, 2012, 11:05:44 am »

Yes it did come with some sort of instructions but it is hard to understand, I will take another look....

Cristiano · « **Reply #7 on:** November 23, 2012, 11:08:44 am »

can you take a picture of the instructions so I can read them?

jaykop · « **Reply #8 on:** November 23, 2012, 11:46:41 am »

Yes will right now 2 mins

jaykop · « **Reply #9 on:** November 23, 2012, 11:53:40 am »

jaykop · « **Reply #10 on:** November 23, 2012, 11:56:25 am »

their is a black and red wire which I have put into the + and the _ is that the right way.... from the red lighton the tacho.

Cristiano · « **Reply #11 on:** November 24, 2012, 03:12:33 pm »

It says that you have to keep the MODE button pushed until the SET led turns ON.

At this point use the UP and DOWN buttons to move the needle to the RPM value that you want the shift light ON.

when you have done, push the MODE button again

SymProjects Forum

News:

Author Topic: how do i get the rev burner to tell me when to change gear (Read 30632 times)

jaykop

how do i get the rev burner to tell me when to change gear

Cristiano

Re: how do i get the rev burner to tell me when to change gear

jaykop

Re: how do i get the rev burner to tell me when to change gear

Cristiano

Re: how do i get the rev burner to tell me when to change gear

jaykop

Re: how do i get the rev burner to tell me when to change gear

Cristiano

Re: how do i get the rev burner to tell me when to change gear

jaykop

Re: how do i get the rev burner to tell me when to change gear

Cristiano

Re: how do i get the rev burner to tell me when to change gear

jaykop

Re: how do i get the rev burner to tell me when to change gear

jaykop

Re: how do i get the rev burner to tell me when to change gear

jaykop

Re: how do i get the rev burner to tell me when to change gear

Cristiano

Re: how do i get the rev burner to tell me when to change gear