« previous next »
Pages: [1]

Author Topic: Pro shift leds  (Read 28465 times)

haggis68

  • Approved Newbie
  • *
  • Posts: 12
    • View Profile
Pro shift leds
« on: July 26, 2011, 07:56:32 pm »
Recieved my pro shift and leds today, i couldnt wait for the jumper cables so i soldered tails onto the leds myself.
 The problem i have is that any led connected and configured through sim dash ( limiter for example ) gives one brief flash the nothing.
I can only assume the voltage is incorrect but i thought the leds supplied should be  "plug n play".

Have i done something wrong or have i been unlucky and recieved a dodgy batch

Any advice/help is most welcome......
Logged

makuwaido

  • Approved Newbie
  • *
  • Posts: 25
    • View Profile
    • Email
Re: Pro shift leds
« Reply #1 on: July 27, 2011, 03:50:23 am »
Just in case, make sure that the value is set to below or above a set value for the led to be constantly working while the condition is met. Leaving it at equal will only turn the led when the value is that one.
Logged

haggis68

  • Approved Newbie
  • *
  • Posts: 12
    • View Profile
Re: Pro shift leds
« Reply #2 on: July 27, 2011, 06:42:55 am »
Even with a condition that is either on or off and the light brightness at 25% the leds seem to be blowing!!!!
Ill wait for the jumper cables before moaning some more...
Logged

Cristiano

  • Administrator
  • Hero Member
  • *****
  • Posts: 1360
    • View Profile
    • SymProjects
    • Email
Re: Pro shift leds
« Reply #3 on: July 27, 2011, 01:47:38 pm »
Quote from: haggis68 on July 27, 2011, 06:42:55 am
Even with a condition that is either on or off and the light brightness at 25% the leds seem to be blowing!!!!
Ill wait for the jumper cables before moaning some more...


Hi.
as quick test: when you connect the Pro Shift  to the computer, start SimDash and open the Pro Shift configuration screen, all the LEDs will turn on.

The LEDs are very bright. usually I leave the brightness set to around 5%.

Regards
Cristiano
Logged

haggis68

  • Approved Newbie
  • *
  • Posts: 12
    • View Profile
Re: Pro shift leds
« Reply #4 on: July 27, 2011, 04:22:04 pm »
as it turns out ive managed to blow 4 green, 1 red and one yellow led. My advice.... make sure you order the proper jumper leads at the same time you order the Pro Shift. It makes life so much easier..

Cheers guys

Pete
Logged

Cristiano

  • Administrator
  • Hero Member
  • *****
  • Posts: 1360
    • View Profile
    • SymProjects
    • Email
Re: Pro shift leds
« Reply #5 on: July 27, 2011, 04:25:46 pm »
Quote from: haggis68 on July 27, 2011, 04:22:04 pm
as it turns out ive managed to blow 4 green, 1 red and one yellow led. My advice.... make sure you order the proper jumper leads at the same time you order the Pro Shift. It makes life so much easier..

Cheers guys

Pete



Are you sure?
How did you connect them?

If you want replacement LEDs, please send an email to me at contact@symprojects.com

Regards
Cristiano

Logged

haggis68

  • Approved Newbie
  • *
  • Posts: 12
    • View Profile
Re: Pro shift leds
« Reply #6 on: July 28, 2011, 06:28:34 am »
Na its ok igot plenty leds lying about. Thanks anyway but if you insist and twist my arm ill have a Rev Burner instead !! lol ;o)

Thanks anyway

Pete
Logged
Pages: [1]
« previous next »
 

hit counter