My WIP dashboard / cockpit

[RAVEN]

Hi, to everyone!!

About the fuel level gauge, I used a resistor between the pin 1 - 3 of black connector;
470 ohm = 100%,
235 ohm (470 x 2 parallel) = 50%,
156 ohm (400 x 3 parallel) = 25%,
or you can easily use a 1Kohm linear potentiometer.

To set the temp level gauge around 50%, you can connect between the pin 17 - 18 of blu connector, a 750 ohm (1.5kohm x 2 parallel) or a 10Khm linea potentiomenter.

[H.Guedes]

Hi, to everyone!!

About the fuel level gauge, I used a resistor between the pin 1 - 3 of black connector;
470 ohm = 100%,
235 ohm (470 x 2 parallel) = 50%,
156 ohm (400 x 3 parallel) = 25%,
or you can easily use a 1Kohm linear potentiometer.

To set the temp level gauge around 50%, you can connect between the pin 17 - 18 of blu connector, a 750 ohm (1.5kohm x 2 parallel) or a 10Khm linea potentiomenter.

And use that why? For test proposes? Because to connect to pro-gauge you don't need any resistor

[RAVEN]

Unfortunally I don't have pro-gauge system, so for a while this is my actual solution.
My intention was to be helpful for those member who already buy 2 Rev burner and would like to see something else move.

[H.Guedes]

Unfortunally I don't have pro-gauge system, so for a while this is my actual solution.
My intention was to be helpful for those member who already buy 2 Rev burner and would like to see something else move.

Like i said, it can be used for test proposes. but they don't move with game data

[H.Guedes]

EDIT:
Ok guys, i have a slight problem...

I Connected only pin 1 to fuel sensor and the pin 4 to speed sensor(black connector), but the fuel level gauge sometimes moves and then seems stuck.
So for me the fuel gauge is not functioning properly, everything else does.

Do i need the OBC to make fuel consumption needle work.??
Anyone have the fuel level gauge settings for 25,50,75% etc. of cfg screen in progauge.??

Any help would be greatly appreciated.
Thankyou everyone for all the help you've already given.  

The fuel consumption need info from the ECU so it's impossible. But with a M3 cluster you can use that with oil temp.

[bruzski]

hello everyone i just registered here but i'm wondering if the fuel gauge issue has been solved

can someone give me the correct schematics incl. the led bulb mod.

[H.Guedes]

hello everyone i just registered here but i'm wondering if the fuel gauge issue has been solved

can someone give me the correct schematics incl. the led bulb mod.

i solve the problem long time ago  

Video testing pro-gauge and arduino with ETS2.

https://www.youtube.com/watch?v=R26cdbtFx_0

[thomasdiaz1201]

Hi. the gauge of speed and rpm inputs only work on rpm and spd. if I plug in another entry not work. Will my chip is broken?

[H.Guedes]

Hi. the gauge of speed and rpm inputs only work on rpm and spd. if I plug in another entry not work. Will my chip is broken?

the speed and rpm gauge is suposed to connect only in rpm and spd. so it's working fine.

[kntkatt]

hi fellas got all my guages working on an e36 cluster apart from fuel does this only work in conjunction with auduino board ?

many thanks

kntkatt

[H.Guedes]

hi fellas got all my guages working on an e36 cluster apart from fuel does this only work in conjunction with auduino board ?

many thanks

kntkatt

Hi. The fuel gauge works with the pro-gauge like the temp gauge and so, and so...

i think some posts up, i explain what is needed to put the fuel gauge working