hidden hit counter

Rev Burner: SimHub Plugin Setup Guide

The Rev Burner SimHub plugin lets SimHub drive a real analog tachometer through your Rev Burner adapter, without SimDash: the needle follows the engine RPM of the game. A simple calibration matches the needle to the dial of your rev counter. The plugin works with every game supported by SimHub.

1. Download the plugin

Download User.RevBurner.zip.

Important: the download is a zip file. Open it and copy the file User.RevBurner.dll that is inside the zip. Do not copy the zip file itself: SimHub does not load zip files.

2. Copy User.RevBurner.dll into the SimHub folder

Close SimHub, then copy User.RevBurner.dll into the SimHub installation folder (C:\Program Files (x86)\SimHub\, unless you installed SimHub somewhere else).

Windows may ask for administrator permission to copy into this folder: click Continue.

3. Start SimHub and enable the plugin

Start SimHub. It detects the new plugin and asks whether to enable it. Switch on the Rev Burner plugin (the switch on the right, which may start switched off), and leave Show in left main menu on, then click Ok.

SimHub asking to enable the Rev Burner plugin
SimHub asks to enable the new plugin: switch it on and click Ok (click the picture to enlarge).

If you clicked Cancel by mistake, you can enable the plugin later from SimHub's Settings.

Still using SimDash for other hardware?
The adapter must be driven by one program only. If SimDash keeps running alongside SimHub, for example because it controls other devices, disable the Rev Burner plugin in SimDash. Otherwise SimDash and SimHub will both move the needle.

4. Configure the Rev Burner

Click Rev Burner in SimHub's left menu. The adapter is detected automatically when you plug it in: the status at the top shows a green dot and Connected - firmware v3.

Rev Burner configuration screen in SimHub: settings and calibration
Rev Burner settings and calibration (click the picture to enlarge).

Firmware v3 required.
The plugin works with Rev Burner adapters running firmware v3. If your adapter has an older firmware, the page shows a message in red and the settings are hidden. Please contact us to update it.

Settings

  • Enabled: when ticked, the needle follows the game RPM. When unticked, the needle stays at rest.
  • Gauge full scale: the highest RPM printed on your rev counter's dial, from 1000 to 20000 RPM (for example 8000 for a dial that ends at 8). The calibration points are based on this value.

When no game is running, the needle is at rest. The adapter is switched on when SimHub detects it and switched off when SimHub closes.

5. Calibrate the needle

Every rev counter needs a different signal to reach the same point of its dial. The Calibration section lists 21 points of the dial, from 3% to 100% of the full scale, with the matching RPM. For each point you set the PPM (pulses per minute) that moves the needle exactly there. Between two points the plugin interpolates, so the needle moves smoothly. Below 3% the needle stays at rest.

  • Slider: drag it and the needle moves at once. Stop when the needle points exactly at the RPM shown on the left.
  • PPM box: type a value and press Enter, then press Test to move the needle there.
  • Test: moves the needle to that point, to check it.
  • Import... / Export...: load or save a calibration file. The files use the SimDash format, so you can reuse a calibration you made in SimDash, or keep a copy of your calibration.
  • Reset to defaults: goes back to the factory calibration.

The PPM values must increase from top to bottom. If they don't, a warning appears in red: check the values you changed.

Stop any running game before calibrating.
Once you move a slider or press a Test button, the plugin ignores the game's data, so the needle stays where you put it. The needle follows the game again when you leave the Rev Burner page in SimHub.

Quick start: calibrating your rev counter

  1. Stop the game and open the Rev Burner page in SimHub.
  2. Select the Gauge full scale of your dial.
  3. If you already have a SimDash calibration for this rev counter, click Import... and you are done.
  4. Otherwise, starting from the top, press Test on each point, then adjust its PPM (slider or PPM box) until the needle shows the RPM written on the left.
  5. Click Export... to keep a copy of your calibration.
  6. Leave the Rev Burner page and start the game: the needle now follows the engine RPM.